No products in the cart.
MQ7 Gas Sensor – Carbon Monoxide (CO)
- Circuit Voltage: 5V
- Heating Resistance: 33Ω ± 5%
- Heating consumption: About 350mW
- Relative humidity: Less than 95%RH
- Detecting range: 20ppm-2000ppm carbon monoxide
₹74.80 Incl. of GSTMQ7 Gas Sensor – Carbon Monoxide (CO)
₹74.80 Incl. of GSTWEMOS ESP32 Development Board – With Battery Holder
- Ultra-low power consumption
- 32 GPIO: ADC(16), SPI(2), I2C(1), UART(1), PWM(32), SDIO(50 Mhz)
- 520 KB SRAM
- 4 MB Flash
- 802.11BGN HT40 WiFi Transceiver (-98 dBm minimum sensitivity)
- Max data rate: 150 Mbps
- -40°C to 125°C operating temperature
₹780.00₹974.00Incl. of GSTWEMOS ESP32 Development Board – With Battery Holder
₹780.00₹974.00Incl. of GSTPower Bank Module – Good Quality
- Charging Voltage : DC 5V
- Charging Current:1000mA
- USB Output Current:1200mA
- Charging Interface Micro USB port
₹85.00 Incl. of GSTPower Bank Module – Good Quality
₹85.00 Incl. of GSTTB6612FNG Motor Driver Module
- Power supply voltage: VM=15V (Max.)
- Output current: Iout=1.2A (ave) / 3.2A (peak)
- Output low ON resistor: 0.5Ω (upper + lower Typ. @ VM ≥ 5V)
- Standby (Power save) system
- CW/CCW/short brake/stop function modes
- Built-in thermal shutdown circuit and low voltage detecting circuit
- Response to Pb-free packaging
₹194.00 Incl. of GSTTB6612FNG Motor Driver Module
₹194.00 Incl. of GSTCH340C ESP32 ESP8266 USB Programmer – USB Type-C
- Chip: CH340C USB-to-Serial Converter
- Interface: USB Type-C
- Power Supply: Powered via USB connection
- Operating Voltage: 5V via USB, 3.3V regulated output for ESP32 & ESP8266
- Operating Temperature: -40°C to +85°C
₹375.00 Incl. of GSTCH340C ESP32 ESP8266 USB Programmer – USB Type-C
₹375.00 Incl. of GSTCP2102 ESP32 ESP8266 USB Programmer – USB Type-C
- Supports ESP32 and ESP8266
- Can support any MCU that needs BOOT & RESET control
- USB-C Type Interface
- LEDs for Power, RX, TX
- Switch for Reset and Boot
- Both 3.3V and 5V available on the O/P connector
₹415.00 Incl. of GSTCP2102 ESP32 ESP8266 USB Programmer – USB Type-C
₹415.00 Incl. of GSTTPA3110 Mono 30W Digital Amplifier Module
- Amplifier Chip: TPA3110
- Working Voltage: DC 8-26V
- Output Power: 1 x 30W
- Applicable Speaker Impedance: 4/6/8 ohm(8 ohms Best)
₹144.00 Incl. of GSTTPA3110 Mono 30W Digital Amplifier Module
₹144.00 Incl. of GSTCC1101 RF Transceiver Module – 868Mhz
- Support FSK, GFSK, ASK / OOK and MSK
- Programmable data rate: 1.2 to 500k Baud
- Vertical Pin header (1.27mm pitch)
- Low voltage input (1.9~3.6V)
- SPI interface
- Independent 64-byte RX and TX data FIFOsCC1101 Core, 433MHz Wireless function
₹265.00 Incl. of GSTCC1101 RF Transceiver Module – 868Mhz
₹265.00 Incl. of GSTSolderless Sanitizer Dispenser Kit
- Solderless Sanitizer Dispenser Kit
- Easy to assemble
- Pre Programmed
- Contains all necessary items except enclosure
- Programmable as per need via onboard ISP Header
₹883.82₹1,180.00Incl. of GSTSolderless Sanitizer Dispenser Kit
₹883.82₹1,180.00Incl. of GSTDSO138 Oscilloscope Kit – Pre Soldered
- Mini Oscilloscope
- Max Input Voltage: 50V Peak (1x Probe)
- Max RealTime Sample Rate: 1 Msps
- Analog Bandwidth: 0 ~ 200 Khz
- Resolution: 12 Bits
- 2.4″ TFT LCD Display
- Power Supply: 9 V
₹1,698.00₹2,006.00Incl. of GSTDSO138 Oscilloscope Kit – Pre Soldered
₹1,698.00₹2,006.00Incl. of GSTYX850 Power Failure Automatic Switching Module – 5V-48V
- Input Voltage Range: 5V to 48V DC
- Switching Current: Up to 10A
- Power Consumption: Low power consumption during operation
- Primary-Secondary Switching Delay: < 10ms
- Operating Temperature Range: -40°C to 85°C
- Mounting: Screw hole mounting for easy installation
₹249.00 Incl. of GSTYX850 Power Failure Automatic Switching Module – 5V-48V
₹249.00 Incl. of GSTR307 Fingerprint Sensor Module
- Operating voltage (v): 4.2 ~ 6 VDC
- Current consumption: ≤75mA
- Verification Speed: ~0.2 sec
- Scanning Speed: ~0.3 sec
- Character file size: 256 bytes
- Template size: 512 bytes
₹802.00 Incl. of GSTR307 Fingerprint Sensor Module
₹802.00 Incl. of GST